Audio Amplifier Selection for Embedded Speakers: A Practical Checklist
To choose an audio amplifier for an embedded speaker, match its low-distortion output power to the speaker’s nominal impedance, continuous power rating, and available supply voltage. At PUI Audio, Inc., we recommend selecting for THD+N of 1% or less and keeping delivered continuous power within the speaker’s rated limit.
Start With the Speaker and Application
Once the speaker and enclosure are selected, collect the information needed to narrow the amplifier options:
- Speaker impedance, typically 4Ω or 8Ω.
- Continuous input power, identified as “Rated Power.”
- Available supply voltage and current.
- Required number of channels.
- Playback content, including tones, voice, or music.
Use the speaker’s continuous rating as your operating limit. A maximum or peak rating is not a continuous-power target, especially for sustained tones.
An amplifier with additional output capability can provide headroom, but the design must still limit the power delivered to the speaker. Set gain and maximum input level accordingly.
Compare Power at the Same Distortion Level
THD+N means total harmonic distortion plus noise. For our selection process, use output power specified at 1% THD+N or less.
A headline wattage measured at 10% distortion cannot be treated as equivalent to the same wattage at 1%. For example, Texas Instruments lists LM4871 headline power ratings at 10% THD+N, alongside 1W continuous average output into 8Ω at 0.5% maximum THD.
Before comparing two amplifiers, align these conditions:
- Load impedance.
- Supply voltage.
- Test frequency.
- Distortion threshold.
- Output power per channel.
Our AMP2X15 illustrates why those conditions matter: its 15W-per-channel specification into 8Ω is stated at 10% THD+N with a 16V DC supply. That figure is not a 15W rating at our 1% selection threshold.
Shortlist Boards by Power Tier and Channel Count
These PUI Audio amplifier boards provide starting points for low-power speaker designs:
| Board | Channels | 8Ω power tier per channel | 4Ω power tier per channel |
|---|---|---|---|
| AMP1X1 | Mono | 1W | 2W |
| AMP2X1 | Stereo | 1W | 2W |
| AMP1X2 | Mono | 2W | 4W |
| AMP2X2 | Stereo | 2W | 4W |
These selection tiers use a 1kHz test signal and THD+N below 1%. Confirm the supply conditions and detailed specifications for the selected board before finalizing the design.
For a 4Ω speaker requiring 2W of continuous input, start with the 2W tier and confirm the speaker is rated to handle that power. Choose mono or stereo according to the application, then verify the completed circuit stays within the speaker’s limit.
Check the Supply and Integration Requirements
A suitable power tier does not guarantee the desired output from every supply. Review performance at the voltage your product actually provides, including its minimum operating voltage.
Check available current with all required channels operating. Also confirm input signal level, gain, connectors, and mounting space before selecting a board.
Amplifier class matters, too. Class D can reduce heat and improve power efficiency, while its switching output requires attention to electromagnetic interference. Compare efficiency at the expected playback level rather than relying only on peak efficiency.
Validate the Complete Audio Path
Before committing to production, test the selected amplifier with the intended speaker, enclosure, supply, and playback content.
- Begin at a low input level and increase it gradually.
- Measure delivered output power and distortion at the intended operating level.
- Confirm continuous power remains within the speaker’s rated limit.
- Check sustained playback, supply variation, and operation with all required channels active.
- Evaluate temperature, background noise, and startup or shutdown artifacts.
Use the manufacturer’s recommended measurement setup, particularly for switching amplifiers. Listening helps assess the user experience, but it does not establish output power or THD+N.
Get Help Matching Your Speaker and Amplifier
Bring us your speaker part number, supply voltage, channel requirements, and intended playback content. Meet with a PUI Audio engineer to discuss an amplifier and speaker combination for your embedded design.
